Review: Sennheiser MD421 Kompakt

Alkuperäinen juttu on ilmestynyt Rockway-blogissa.

****

****

In 1960, Sennheiser’s perhaps best-known microphone, the Sennheiser MD421, was released. The MD421 is a rather large and heavy microphone, and it is designed in quite a unique way.

This microphone uses a rather massive capsule with a large (27 mm/1.1 inch) diaphragm, which is carefully protected from handling and wind noise. In addition, the capsule has its own humbucker coil, which filters out electromagnetic hum and buzz out of the microphone signal.

A short “bass pipe” extends from the bottom of the capsule into the center of the microphone housing, which acts as a “bass chamber.” Depending on the year of manufacture of the MD421, this chamber may be either simply the plastic housing of the mic, or there may even be an injection-molded metal chamber inside the microphone.

A five-position rotary switch for the bass cut is embedded in the end of the housing – one extreme position “M” (Musik; music) lets the MD421 pass through the entire frequency range, while the second extreme position “S” (Sprache; speech) effectively removes most of the bass frequencies from the signal.

The new Sennheiser MD421 was available in versions with the German Klein-Tuchel connector (a larger and sturdier cousin of the DIN connector), as well as with an XLR connector.

The new model’s stand adapter was quite unique; the adapter had a long swivel leg on the stand side, while on the side that went into the microphone there was a rail with a spring mechanism. This rail is pushed into a groove in the belly of the microphone until the mechanism clicks into place.

The Sennheiser MD421 model became a huge sales success upon its release. Although the new microphone was relatively expensive, the quality of the MD421 was so convincing that the microphone was seen in almost every TV studio, concert stage, podium, and recording studio in the 1960s and 1970s – especially in Europe. When I was six years old, I had two things I wanted desperately to own – a Fender Jazz bass and “that creamy white Sennheiser”.

Although the MD421 was originally intended to be “everywhere”, over time the special strengths of the microphone led to it being seen most often in front of brass instruments, drums, and guitar and bass amplifiers.

The Sennheiser’s light-colored housing was permanently changed to black sometime in the late 1970s, and parallel versions of the MD421 were also introduced, for example some without an internal bass filter.

The Sennheiser MD421 has maintained its position, especially in the recording studio, to this day. The only criticisms are the model’s large size and weight, which can make it difficult to position the mic, and the reliability of the mic adapter, especially in heavy use. A microphone bouncing from a tom onto the drummer’s lap is not likely to inspire much confidence.

****

Sennheiser has finally listened to everyone who has been asking for a scaled-down version of the MD421 model. A few weeks ago, the Sennheiser MD421 Kompakt, a compact parallel version of the old classic, was released.

The Kompakt version (street price around 290 euros) is almost half the length of the original MD421 (12 cm versus 21.5 cm) and more than half the weight (159 g versus 385 g).

The microphone capsule in the new Kompakt version is exactly the same as in the classic version, and the volume of the bass chamber in the shorter body has been kept the same size. Thanks to this, it is no surprise that the frequency response (30 Hz – 17 kHz) and other technical values ​​​​of the MD421 Kompakt are also identical. The microphone’s shrinkage has been achieved by removing the bass filter unit of its big brother from the Kompakt.

The Sennheiser MD421 Kompakt does not have a separate stand adapter, but here it is implemented as part of the microphone body. For drum recordings, the new mic is also available in a set version (street price approximately 315 euros), which already includes the MZH drum adapter suitable for the Kompakt. A storage bag is included in both sales packages.

The convenient size and low weight of the MD421 Kompakt make it very easy to place the new mic. The more compact body does not feel toy-like at all, but the mic has the same solid construction as its big cousin. I think the MD421 Kompakt would also be an excellent choice for a vocal mic on stage, as you don’t have to worry about your teeth, as you would with the full-size version, if someone hits the mic stand while you’re singing.

****

At least to my ears, the Sennheiser MD421 Kompakt sounds a little warmer than a Shure SM57, and the new mic’s presence emphasis is also at a higher frequency than the Shure. Whether this is a “good” or “bad” feature depends entirely on the source signal and your own preference.

****

For this review I recorded two demo songs with the Sennheiser. The first demo is a completely acoustic song, where every instrument and sound has been recorded with the MD421 Kompakt and a Cranborne Camden EC2 mic preamp. Song number two is a rock song, where the drums sounds are samples, but the bass and guitars have been captured with the MD421 Kompakt and the built-in microphone preamp of Universal Audio’s Volt 2 interface.

****

Testipenkissä: Raato Guitars Fuzzrocity

Raato Custom Guitars on tunnettu pajan nykytarpeisiin tehdyistä huippulaadukaista sähkö- ja bassokitaroistaan. Raato Guitarsin pomo Mika Ruotsalainen on hiljattain lisänyt kolme efektipedaalia brändin valikoimaan – yhden trebleboosterin, sekä pari fuzzia.

Upouusi Raato Fuzzrocity (268 €) on Fuzz Face -tyylinen piipohjainen fuzz-särö nykyajan kitaristeille. Tässä yhteydessä ”Fuzz Face -tyylinen” tarkoittaa nimenomaan efektin soundimaailma, sillä Fuzzrocity ei ole missään nimessä jonkun vintage-pedaalin klooni.

Kun kävin pajalla, Mika näytti minulle muutaman työn alla olevan Fuzzrocity-pedaalin. Hän käyttää erittäin laadukkaita osia, sekä oman suunnittelun mukaan tehtyjä piirilevyjä. Myös pedaalien grafiikat etsataan itse Raato Guitarsilla. Toimiakseen Raato-pedaalit tarvitsevat Boss-standardin mukaista yhdeksän voltin virtalähdettä.

Hyvä vintage Fuzz Face voi olla taivaallinen soundikokemus, mutta valitettavasti sillä ei ole paljon mahdollisuuksia säätää sitä soundia, kun tarjolla on ainoastaan Fuzz- ja Volume-säätimet. Riippuen soittajan musikkillisista tarpeista, sekä käytetystä kitarasta ja vahvistimesta, vintage-fuzz voi kuulostaa liian terävältä tai liian mutaiselta, etenkin nykyaikaisten alavireisten (tai seitsenkielisten) kitaroiden kanssa.

Lisäksi vanhat Fuzz Facet voivat aiheuttaa ongelmia yhteiskäytössä wah-pedaalin kanssa. Pedaalien välinen impedanssin yhteensopimattomuus voi aiheuttaa korvia raastavaa ulinaa.

Raato Fuzzrocity on suunniteltu nykykitaristin tarpeita silmällä pitäen – pedaali tarjoaa laajan valikoiman herkullisia säröjä, sekä paljon säätövaraa eri genrejä ja tarpeita varten. Efektistä löytyy neljä säädintä:

BIAS antaa sinun säätää piitransistorien käyttöjännitettä, kun taas HPF tarkoittaa ylipäästösuodatinta, jolla voit poistaa särösignaalista mahdollisesti häiritseviä bassotaajuuksia. FUR vastaa tavallista fuzz- tai gain-säädintä tulosignaalille, kun taas LEVEL ohjaa lähtösignaalin voimakkuutta.

Lisäksi Fuzzrocitysta löytyy kolmisuuntainen minikytkin, joka antaa sinulle kaksi eri treble-filtteriä (sekä ohituksen keskiasennossa), jolla voi kesyttää tarvittaessa signaalin diskanttia.

Saat nykyaikaisen version Fuzz Face soundista, kun BIAS on lähes täysillä ja HPF pois päältä, jolloin FUR ja LEVEL toimivat vintage-faced Fuzz- ja Volume-säätimien tavalla. Ehdottaisin, että laitat tässä tapauksessa diskanttifiltterin kytkimen ala-asentoon.

Raato Fuzzrocity tarjoaa kuitenkin paljon laajemman kattauksen eri fuzz-soundeja, kun ottaa kaikki säätimet käyttöön.

BIAS-säätimen asetuksilla on erittäin suuri vaikutus tämän pedaalin luonteeseen ja dynamiikkaan. Matalilla BIAS-asetuksilla saat ”kuolevan pariston” soundeja, joissa esiintyy vahva geittaaminen ja hyvinkin rakeinen särösoundi. Avaamalla BIASia fuzz-sounds muuttuu kiinteämmäksi ja dynaamisemmaksi. Monet nyky-rock- ja metal-kitaristit hyötyvät pedaalin HPF-säätimestä, joka on tärkeä työkalu, silloin kun halutaan pitää mutaisia bassotaajuuksia aisoissa. FUR-säädin käyttäytyy – luonnollisesti – vuorovaikutteisesti BIAS-säätimen kanssa, ja sen soundien skaala ulottuu ”rikkinäisen sitarin” soundeista mietojen overdrive-soundien kautta tuomiopäivän fuzziin. Kolmiasentoinen treble-kytkin toimii hienosti purevuuden annostelijana.

Mika Ruotsalainen on suunnittelut Raato Fuzzrocity -pedaalinsa toimimaan saumattomasti myös vintage-tyylisten wah-wah-pedaalien kanssa, niin kuin kuulee tämän jutun alussa olevassa videossa, jossa käytin Voxin V845 suoraan Fuzzrocityyn.

Jutun lopussa oleva video taas näyttää, kuinka hyvin Fuzzrocity reagoi kitaran volume-säätimen muutoksiin.

Minun mielestäni Raato Guitarsin Fuzzrocity-särö on täysosuma, koska sillä saa erittäin laajan valikoiman erilaisia vintage-vivahteisia fuzz-soundeja, täysin ilman vintage-klooneille tyypillisiä ongelmia monissa nykypäivän genreissä.

Fuzzrocity-pedaali on piensarjoissa käsin tehty efekti, ja saatavilla hyvin järkevällä hinnalla. Pedaalilla on selkeästi luottotyökalun ainekset.

Review: Raato Guitars Fuzzrocity

Raato Custom Guitars is a Finnish maker of ultramodern handcrafted electric guitars and basses. Recently Raato’s main man Mika Ruotsalainen has introduced three effect pedals – a treble booster, as well as a pair of fuzz-boxes.

The Raato Fuzzrocity (268 €) is a Fuzz Face-flavoured silicon fuzz made for the modern guitarist. When I say ”Fuzz Face-flavoured” I mean the character of the fuzz sound, but the Fuzzrocity is not a clone of a vintage Fuzz Face.

Mika showed me a few Fuzzrocity pedals he was working on, when I visited his workshop, and I could see he was using high-quality parts and bespoke pcbs to assemble his pedals. The custom graphics are also etched into the pedals’ casings right there in the workshop. The pedal is powered by a Boss-standard 9V power supply.

A vintage Fuzz Face can be a thing of beauty, but it doesn’t offer much scope for adjustment, offering only Fuzz- and Volume-controls, without any option to adjust the resulting fuzz sound itself. Depending on the player’s requirements and equipment a vintage fuzz can sound too bright or too muddy, especially with modern downtuned (or seven-string) guitars.

Additionally, many original Fuzz Faces have a tendency to self-oscillate when used in conjunction with a wah-wah, due to impedance mismatching caused – in most cases – by the wah-pedal.

The Raato Fuzzrocity has been designed from the ground up to give you all of that delicious sound, while also offering plenty of scope for adjustment. There are four controls on offer:

BIAS lets you adjust the operating voltage for the silicon transistors, while HPF stands for ”high-pass filter” and lets you dial out any bottom end that might be clogging up your sound. FUR corresponds to your regular fuzz- or gain-control for the input signal, and LEVEL controls the output level.

Additionally, there’s a three-way mini-toggle that gives you two low-pass filter setting (plus bypass in the middle position) to tame the signals treble content, if necessary.

To get a modern version of a Fuzz Face sound, start off with the BIAS around 4 o’clock and the HPF turned to 7 o’clock. With this setting FUR and LEVEL correspond to a two-knob fuzz’s Fuzz- and Volume-controls, respectively. I’d recommend you set the three-way toggle to the downward position in this case.

But there’s a much wider array of tones to be gleaned from the Raato Fuzzrocity by using the controls to their fullest.

Settings of the BIAS-control have a very large bearing on the character and dynamics of this pedal. Set low BIAS will give you the sound of a ”dying” battery with plenty of gating and graininess. Turning BIAS up gradually will give you firmer fuzz sounds and more dynamic variation. For modern applications with drop-tuned and/or seven-string electrics and baritones, the HPF-knob is a crucial tool to keep any unwanted wooliness at bay. The FUR-control is – naturally – interactive with the BIAS settings, and it will take you all the way from ”broken sitar” tones and mild overdrive to doomsday fuzz. The three-way treble switch is really useful in tailoring the table content to suit your needs.

Mika Ruotsalainen has designed the Raato Fuzzrocity to work well with vintage-style wah-pedals, as you can easily hear in the video at the top of this review, where I have a Vox V845 running directly into the Fuzzrocity.

The video at the bottom of this video will show you for its part how well the Fuzzrocity responds to changes at your guitar’s own volume control.

In my view the Raato Fuzzrocity is a success on all fronts, because it manages to give you a wide variety of vintage-inspire fuzz sounds, without the drawbacks of vintage clones, and with far greater scope for adjustments.

The Fuzzrocity is handcrafted in Finland in very limited numbers and sold at a very reasonable price. This could easily become your go-to fuzz from now on.

Raato Guitars Fuzzrocity – Demo Song

Here’s a demo featuring the Raato Fuzzrocity Silicon Fuzz. The Raato Fuzzrocity is handmade in Finland.

• Rhythm guitars – Squier Sonic Mustang SS & Harley Benton DC-60 Jnr

• Harmony guitars – Hamer USA Studio Custom

• Lead guitar – Jackson JS32 Dinky Archtop

• Pedals used – Raato Fuzzrocity & Vox V845 Wah-Wah

• Amp used – Bluetone Black Prince Reverb

• Mic used – Shure SM7B

Play-along – ”Spanish Eyes”

The tab I use is read as follows:
• plain numbers are ”channel blown”; 2 = second channel blow
• minus numbers are ”channel drawn”; -4 = fourth channel draw
• brackets mean ”slider pressed in”; (-7) = seventh channel draw with the slider pushed in

Pidä blogia WordPress.comissa.

Ylös ↑