It was actually the bass that served as the original impetus for the Hallabird. Ville had made a slightly Gibson Thunderbird-influenced bass for his own use. The bass got so much positive attention that Ville decided to put more bread on the water, which is why he developed a guitar model along the same design ideas.
The Halla Custom Hallabird (3,700 €; including case and more, see below) is a handmade neck-through guitar with a flawless clear finish.
The through neck is made from nine long strips of wood – African mahogany (khaya ivorensis) offset with walnut. While the neck construction follows Gibson’s lead, the Hallabird takes its own path when it comes to scale length. This custom guitar comes with an extra long scale length of 67 cm (that’s approximately 26.37 inches for our Imperial readers).
The streamlined body wings have been crafted from khaya, too.
The Hallabird comes equipped with black Gotoh-hardware. This guitar also sports a brass nut to insert a little brightness into the open strings. This is probably the smoothest brass nut I’ve seen in my guitar-playing life.
Access to the two-way truss rod is from the headstock end on this Halla Custom guitar.
Twenty-four gleaming Jescar Evo jumbo frets have been installed into the Hallabird’s ebony fingerboard. The fretwork is nothing short of excellent – this is one of the areas where a handcrafted guitar tends to outshine production models, regardless of their price.
Gotoh’s hardware is known for its consistently high quality, and the Hallabird’s TOM-bridge and stopbar are no exception.
Ville Mattila mostly uses his own pickups in his Halla Custom guitars. The Hallabird comes equipped with a pair of handmade P-90s, niftily placed inside EMG-style plastic covers. The pickups are reverse-wound/reverse-polarity, meaning they act as a humbucker, when used together. The pickups’ golden polepieces look great with the Jescar EVOs and the khaya mahogany.
The Hallabird’s electronics are a little bit different than what you’d expect, judging by the knobs. There’s a three-way toggle for pickup selection, as well as a master volume control (sans treble bleed). What looks like a tone control is in fact what Ville calls a three-way impedance rotary. While the rotary switch minutely changes the treble content of the overall signal, it clearly influences the volume control’s roll-off taper. This allows you to fine-tune the way the guitar’s volume control reacts to your playing style and your amplifier.
Halla Custom’s Hallabird is one heck of a guitar. It is one of these rare cases, where a new design manages to look classic and fresh at the same time. A guitar that is understated, yet flashy. The quality of workmanship is excellent down to the smallest details.
The Hallabird is very lightweight, making it an ideal choice for long sessions or gigs. Thanks to the guitar being a non-reverse design, the Hallabird balances very nicely despite its longer-than-usual neck.
The neck profile is reassuringly round and chunky, without feeling clunky or unwieldy. Thanks to the outstanding fretwork the Hallabird came with a setup that made a set of 010s feel very slinky, even on the extra long scale neck. I’m quite sure many players won’t even notice the extra scale length, but if you wanted to order something more ordinary, I’m sure that Ville would happily oblige.
Acoustically, the Hallabird displays a piano-like attack with a long and even sustain. Note separation is excellent, even with complex chords, and there’s a great balance between warmth and clarity.
P-90s are a fantastic choice if you need humbucker-type power and girth, coupled to a single-coil’s dynamics. Even though its looks are probably a little ”too Rock”, the Hallabird can glide effortlessly into Country and Jazz mode, and then turn into a Rock machine at the proverbial drop of a hat.
These two clips have been recorded using a 1980s Boss SD-1 and a Bluetone Shadows Jr. boutique combo:
For the demo song I used a 1980s Ibanez SC10 chorus pedal on the rhythm guitars, and a Morley M2 Wah for the lead, through the Shadows Jr.:
Halla Custom’s Hallabird is a great-sounding and classy-looking guitar, made by somebody who clearly knows what he is doing. Don’t be fooled by the Classic Rock looks – this is a very versatile instrument for the discerning player.
Naturally, handcrafted quality like this never comes cheap. This is a true boutique guitar, made by a trained luthier-artisan highly dedicated to his craft.
Halla Custom Hallabird
Handmade neck-through electric guitar
3,700 € – includes hard case, high-end guitar cable, quality strap (with Schaller locks), one free setup (after 6-12 months of use), and lifetime tech support
Contact: Halla Custom Instruments
+ handcrafted in Finland
Halla Customs’ Ville Mattila is a member of the Guild of Finnish Luthiers.